Why does water appear in the washing machine?

The appearance of a brand new washing machine in the house is always a joy for every housewife, because a lot of problems, such as washing by hand, rinsing, will disappear. So - there will be no cost of extra effort and time. But, like any technique, a washing machine can fail, for example, just before laying the laundry, you find that water appears in the washing machine. Fortunately, such a breakdown does not occur so often, and in order to restore the device’s operability, it is only necessary to correctly identify the cause of the malfunction and begin repair. In most cases, the wizard is not needed - you can remove the problem yourself.

to contents ↑

Why is water collecting in the washing machine?

Almost all washing machines are equipped with leakage protection. This is done so that water from the drum could not leak out, and thereby did not cause a flood. Without exception, all modern washers are equipped with check valve systems that prevent water from entering the washing machine when it is not in use.

Despite all the precautions, water in the drum of the washing machine can still appear by itself, which means that the first thing to do is determine the source of water in the turned off washing machine.

To do this, you need to analyze the water in the tank:

• If the water is dirty and has a specific smell of wastewater, then there is a wrong connection of the washing machine to the sewer.
• If the water is clean and odorless, then it got into the washer from the water supply.

Summarizing the above, we can name the main causes of the appearance of water in the washing machine:

1. Incorrect unit connection or sewage problems.
2. High level of installation of water discharge.
3. Clogging, both in the sewage system and in the device itself.

Consider specific cases when water is collected in the washing machine and identify ways to solve problems.

to contents ↑

Situation number 1

The essence of the problem is that a few days after washing, water appears in the tank of the unit.

To solve this malfunction, turn off the water supply tap to the machine:

1. If water still appears, then the problem is in the wrong device to drain the water. Often waste water gets into the washer due to improper connection of the sewage system, or rather, due to the poor position of the drain hose. Therefore, correct the unit connection by referring to the manufacturer's instructions and recommendations. On our portal you can also find information how make the right drain. If everything is connected as it should, then the source of the problem may be a blockage in the pipe, and water flowing into the sewer accumulates inside the machine, not finding a way out and climbing the hose. The solution is simple - remove clogged drain hose or pipe.
2. If water does not stop appearing, then alas, you will have to disassemble the unit, since there is a possibility of breakage of the shut-off inlet valve. The causes of the problem may be:
   • Poor water quality in which sand and small pebbles are present. Result - the valve becomes clogged and stops functioning normally. In this case, it is better to install filters for water purification in the apartment.
   • Valve wear. Correct the situation can only replace the valve.
   • Failure of any other element of the washing machine or wiring, which causes a short circuit, and the resulting current starts the valve.To fix the problem, you need to find the faulty element and repair it.

Important! If you are able to repair the unit yourself, then get down to business, if not, then use a simpler solution: turn off the water supply tap after each wash.

to contents ↑

Situation number 2

Another manifestation of how water appears in the washing machine - immediately after washing, it remains inside the tank.

To solve the problem of such a plan, it is necessary to check the drain filter located near the floor behind a large decorative cover. In order to do this and, if necessary, clean it of dirt, proceed as follows:

1. Drain the water manually from the hose, otherwise the water will spill directly onto the floor.
2. Remove the panel.
3. Clean the filter from dirt and small debris.
4. Inspect the pump located behind the filter, and if it is clogged, it must also be cleaned.
5. Replace the clean filter.

to contents ↑

Situation number 3

Another option for how water is collected in the washing machine is the most difficult. In such a situation, it does not merge at all at the end of the cycle.

If the washer still tries to drain the liquid and at the same time buzzes, then most likely it is required pump replacement or repair. To solve this problem, call the wizard - you can’t do it without your own hands.

to contents ↑

Situation number 4

A less difficult situation is that the water is drained from the machine, but not completely.

If you have just such a problem, then most likely either the pump began to work less efficiently, or you have problems with the water level sensor.

Important! You can check the operation of the pump yourself by placing the drain hose below an existing level.

to contents ↑

Stock footage

We hope that our tips and tricks will help you diagnose the washing machine and identify the causes of the problem. If you doubt your abilities, then turn to specialists who will quickly and accurately fix the device. But first, try to conduct an investigation and repair yourself, so as not to waste money and time.