Drain hose for washing machine

The presence of a washing machine will not surprise anyone. Therefore, everyone should know how to solve certain problems arising with this technique. One of these is the drain hose for the washing machine. This article will talk more about how to solve the problem. Only 2 outputs:

  1. Purchase of a new hose of the required length.
  2. Extend an existing handset.

We consider these processes in more detail later in the text.

to contents ↑

Geometric features

In order to replace or build up a drain pipe, you need to understand the features of its geometric structure. As a rule, installation of the tube included in the kit is already carried out by the manufacturer. This provides absolute protection against leaks and other malfunctions of this part.

The washing machines are designed so that the water pressure does not exceed a certain pressure, while draining the water from the pipe can be stopped with a finger:

  • Given this factor, the top point of the hose should not be above 100 cm. Otherwise, the pump simply cannot push the water out.

Important! The highest point is considered to be the height of the pump. However, it is enough to position any point of the outlet hose to this height.

  • On the other hand, the same point should not be lower than 60 cm relative to the lower point of the device. The minimum height value is always indicated in the installation and operating instructions. This recommendation is needed so that water, when entering the drum of the machine, does not immediately overflow into the sewer.

Important! To organize the drainage into the sewer of a kitchen sink, it is recommended to use a height of 90 cm. This avoids periodic blockages.

to contents ↑

The process of lengthening the drain hose

Before lengthening the drain hose of the washing machine, you will need to purchase:

  1. A drain pipe of the required length, of the same brand as in the kit.
  2. Hose connector
  3. Clamps for clamping.

The process of lengthening itself is conditionally divided into 3 stages:

  1. Buying the necessary material suitable for your model of washing machine. If it is impossible to find an identical tube, you need to find the most similar in characteristics, the most important of which is the diameter.
  2. Preparing to install an extension cord. The entry of the connector into the drain hose must be very tight. The joints should be in the middle of the tube.
  3. Fixing tips with clamps. The tightness must be strong enough to prevent breaks and subsequent leakage.

Important: Before starting the machine, once again check all the fasteners for reliability. Gluing the tubes together will be most appropriate - this provides the most reliable sealing.

Important! No matter how reliable and expensive the equipment may be, sooner or later errors may occur in its operation. Manufacturers took care of this - if a malfunction occurs, a code is displayed on the display. We have prepared separate articles in which you will find error codes for washing machines of well-known brands, as well as tips for resolving them:

to contents ↑

Types of hoses

Regardless of the fact that the washing machine’s drain hose function is always the same - discharge of dirty water, the market provides several varieties of it:

  1. A regular hose of a fixed length - varies from 1 to 5 meters. If necessary, it can be lengthened.
  2. The telescopic type is a fairly universal option. Such parts are sold in compressed form, and when stretched, increase their length up to 3 times. They also have their drawbacks. Hoses of this type are most susceptible to damage and blockages.
  3. Hose in the bay. It is a long tube with a module of 50-55 cm. It is convenient in that it can be cut on a serif made modulo. And that means you can do the necessary length yourself.

Important! It is not recommended to use a length of more than 3 meters, since the longer the length, the greater the likelihood of clogging or damage. And such things lead to breakdowns not only of the drainage system, but also of the machine as a whole.

Among the general characteristics for each type are the following:

  1. The material of manufacture is polypropylene.
  2. At the ends, there are so-called fittings with a diameter of 19 to 22 mm made of rubber.

Important! In order for the washing machine not to fail for a long time, from the first day it is necessary to use it correctly and carry out preventive measures. For more information, see the article."Caring for a washing machine".

And with power surges, use a voltage stabilizer or network filter.

to contents ↑

Ways to organize a drain

Water can be drained in several ways. The thoughtfulness of the design of the drainage system largely depends on this. We will analyze the most popular options:

  1. Drain into the sink or bathroom. For this method, it is enough to insert a hose to drain the water into the holder and direct it into the bathroom or sink. This method is used when it is impossible to connect to the sewer or temporarily use the machine in this place.

Important! This option has its drawbacks: the inability to use the bathroom / sink during washing, pollution due to waste water, unpleasant appearance of the device.

  1. Connection to the sewerage by means of a siphon. The best option for many cases. Sufficient sealing is provided for ease of use.

Important! The disadvantage of such a system is that it occupies a certain place.

  1. Installation directly into the sewer through the cuff. In this method, it is necessary to ensure that there is a margin of length for the drain hose of the washing machine. The hose must not be taut, as vibrations can damage the joint, leading to leakage.
  2. Siphon with check valve. This connection method is rarely used in our time, since in most apartments there is no special place for devices such as a washing machine or dishwasher.

Important! This type of mechanism is significantly superior to the previous ones, as it has a system of protection against unpleasant odors and the return of water into the equipment.

Important! Do not overload the washing machine, so that expensive mechanisms do not fail. Follow the link and find out how to calculatethe weight of the laundry.

to contents ↑

General recommendations for replacement or extension

Each washing machine is individual, respectively - the instructions for replacing the hose are different everywhere. But there are a number of general rules for each of them:

  1. The first thing to do is turn off the machine from the mains. At the same time, secure the power cable to the back of the device.
  2. The next step is to disconnect from the water supply. In this case, pay attention to the pipe laying. It must not be allowed to get lost.
  3. At the place of attachment of the drain, you need to put a cap, and the drain hose for the washing machine itself is fixed to the back wall with the pipe up.
  4. Next, you should get access to the place where the hose is fastened - usually this is a connection to the device’s drain pump.
  5. Next, the tube is disconnected and removed. You also need to disconnect it from the sewage system and carefully drain the remaining water.
  6. The last item is replacing the old hose with a longer new one.

Important! How to get to the drainage system of the washing machine itself is carefully described in the operating instructions from each manufacturer. Installation instructions for a new pipe are also presented there.

to contents ↑

Stock footage

Installation of a hose for draining water is a fairly simple matter if you understand some of the subtleties described above. And this means that you probably will not need the help of a specialist, and you will successfully mount everything yourself. Remember, following the instructions is the key to success.

1 star2 stars3 stars4 stars5 stars (No ratings yet)
Loading...

Report typo

Text to be sent to our editors:

Adblock detector

Wardrobe

Electronics

Wash