How to remove a film from plastic windows

The protective tape covers the frames of plastic double-glazed windows in order to protect them from dust, dirt and scratches during transportation and installation. Therefore, the instructions, the protective tape must be removed within 10 days after installing the plastic glass. But you need to know how to remove the film from plastic windows correctly, otherwise as a result you will get damaged structures that will have to be restored or reinstalled.

to contents ↑

Why is it difficult to peel off the window?

The composition of the protective tape includes two layers that are glued to the frame using a special solution. The inner coating is thin, very tightly attached to the plastic profile. It begins to be absorbed into its surface under the influence of the following factors:

• ultra-violet rays;
• the use of low-quality glue when applying a protective tape to the frame;
• exposure to heat enhances the absorption of glue in plastic.

Important! Before you remove the film from plastic windows, properly tune in to the process so as not to be nervous and not in a hurry. Please note that if you decide to remove the protective shell immediately after installation, then this procedure will not take you much time and effort. But in the event that you do not do it in a timely manner - get ready to work a few hours.

to contents ↑

How to remove the film from plastic windows?

Before you begin this procedure and remove the film from the plastic windows, decide how you will do it. You will need:

• building or household hair dryer;
• scraper for cleaning glass-ceramic surfaces;
• denatured alcohol;
• eraser;
• acrylic solvent;
• White Spirit;
• Cosmofen
• means “Fenosol“.

Important! Do not use caustic solvents to remove such a coating from the frame, as it may damage the surface of the plastic.

to contents ↑

How to remove a film from plastic windows?

If you decide what to wash the windows from the film, then proceed with the action. Follow the next few steps.

Stage 1

At this stage, you will remove the easily adhered material:

1. Take the knife.
2. Cut them a protective tape, acting very carefully so as not to scratch it.
3. Remove the shell from the outside and inside of the frame.

Stage 2

With these steps, you will steam out small sticky pieces of tape:

1. Take a construction hair dryer.
2. Preheat the remaining pieces of material with it.
3. Clean them with a special scraper for cleaning glass and ceramic surfaces.

Important! Do not direct the air flow to the glass unit, but only to the frame in order to avoid damage to the glass from temperature differences.

Stage 3

Before you clean the plastic windows from the remnants of the film, prepare a soap solution and do the following:

1. Take a linen cloth.
2. Soak it in soapy water.
3. Wipe the frame.
4. Wait until a soapy crust appears on it.
5. Remove it with a dry cloth.
6. Rub the rubber seals with a damp, then dry, rag.

to contents ↑

How to wash windows from sunscreen?

In hot and sunny summer weather, many apply sun-protection film to the glass in order to protect themselves from bright scorching rays. But, unfortunately, under the influence of heat and ultraviolet radiation, the material is eaten into the surface of the window.In autumn and winter, there is no need for such a device, and in order to ensure the best heating of the room in a natural way, there is an urgent problem, how to clean the window from sun-protection film. To simplify this procedure, use our tips.

Method 1

The effectiveness of this method has been tested by many in their experience. To use it, do this:

1. Take the meth.
2. Pour it into the spray bottle.
3. Spray onto the sunscreen.
4. Wait a couple of minutes.
5. Pry the edge of the casing with a knife.
6. Remove it gradually.
7. Repeat the procedure as necessary.

Important! Remove any remaining glue marks with Cosmofen or Fenosol.

Method 2

The most effective way to clean the window from sunscreen. To use it, do the following:

1. Take a steam generator.
2. Heat the surface of the frame with it.
3. Pry off the material to be removed with a knife.
4. Tear it off without stopping.
5. Remove glue marks with acrylic solvent.

Important! Instead of a steam generator, you can use a construction or household hair dryer.

Method 3

For this method, you will need an eraser to erase the pencil and white spirit. Please note that the process will be long and laborious, but the result will be high-quality. Use such tools as follows:

1. Take a school eraser.
2. Rub and remove with it the sun protection film from the window.
3. Remove glue marks with white spirit.

Important! If you are hesitant to apply more than one of the proposed options, contact a cleaning company. For these purposes, they have all the necessary tools and devices - with their help they can easily solve your problem, how to remove the old film from plastic windows.

to contents ↑

Stock footage

We hope that our article was useful to you and made it easier for you to remove the film. Surely, your windows shine with purity and delight you. But remember that this process does not cause you any difficulties, the next time remove the protective tape immediately after installing a new plastic double-glazed window and do not forget to look after it correctly afterwards.